Go Back   Club Bazooka > Search Forums

Notices

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: heavyduty
Forum: Amplified Tube Subwoofers 11-17-2017, 02:01 PM
Replies: 232
Views: 102,656
Posted By heavyduty
Re: FAST-9999 Installaton Instructions

Only if you can clearly identify the correct wires as labeled in the schematic. If harness 17P, does not match up with the schematics you are looking at, then I would move on to the next harness...
Forum: Amplified Tube Subwoofers 11-16-2017, 01:06 PM
Replies: 232
Views: 102,656
Posted By heavyduty
Re: FAST-9999 Installaton Instructions

What type of factory system do you have? If it is the stock, 4 speaker, no premium sound system or navigation, you should be working with harness 14P. Can you post back with what type of factory...
Forum: Raw Woofers 11-10-2017, 01:11 PM
Replies: 2
Views: 149
Posted By heavyduty
Re: Parameters for 6" driver

As luck would have it, I can get you the specifications for the Euphonic components and those sweet Revolver tweeters. I'll post those when I get a chance to look through my material.
Forum: Amplified Tube Subwoofers 11-08-2017, 04:21 PM
Replies: 1
Views: 58
Posted By heavyduty
Re: LOC or Bazooka high-level inputs?

What year, make and model, are you installing the Tube in?
Forum: Amplified Tube Subwoofers 10-31-2017, 08:38 AM
Replies: 232
Views: 102,656
Posted By heavyduty
Re: FAST-9999 Installaton Instructions

No, again, it is an either/or method of input signal, not both. However, the preferred method with the BTAXX100 line, is to use the High Level Inputs.
Forum: Amplified Tube Subwoofers 10-30-2017, 03:19 PM
Replies: 232
Views: 102,656
Posted By heavyduty
Re: FAST-9999 Installaton Instructions

Are you referring to the RCA's? If so, you can use High Level Inputs (which would be connecting to the existing harness for an input signal), or Low Level Inputs (using a patch cord, or RCA cable). ...
Forum: Amplified Tube Subwoofers 10-04-2017, 07:51 AM
Replies: 1
Views: 134
Posted By heavyduty
Re: Fried nos8 amp

Give Technical Support a call at 1-800-THE-TUBE.
Forum: Amplified Tube Subwoofers 09-26-2017, 08:10 AM
Replies: 9
Views: 199
Posted By heavyduty
Re: Bazooka BTA10100 not working correctly please help!

You can use the rear speakers or the front speakers for the High Level Input Signal. I would use the larger speakers of the two. This can be done at the speakers or at the harness. Do you have a...
Forum: Amplified Tube Subwoofers 09-25-2017, 03:45 PM
Replies: 232
Views: 102,656
Posted By heavyduty
Re: FAST-9999 Installaton Instructions

You only need to tap two wires, plug in the RCA's, and connect to a proper ground.
Forum: Amplified Tube Subwoofers 09-25-2017, 02:55 PM
Replies: 232
Views: 102,656
Posted By heavyduty
Re: FAST-9999 Installaton Instructions

Then use the RCA's for the signal input, and connect the constant +12v to the constant +12v of the headunit/harness, the switched +12v to the key-on/key-off source at the harness and of course the...
Forum: Amplified Tube Subwoofers 09-25-2017, 02:42 PM
Replies: 232
Views: 102,656
Posted By heavyduty
Re: FAST-9999 Installaton Instructions

Not a dumb question at all. You can connect anywhere in the harness, as they are all going to the speakers. For the best performance, connect to the front speakers. Unless they are of an extremely...
Forum: Amplified Tube Subwoofers 09-25-2017, 08:56 AM
Replies: 9
Views: 199
Posted By heavyduty
Re: Bazooka BTA10100 not working correctly please help!

Thanks for posting the picture. Unfortunately I could not see enough of the ground you were referring to. Be sure to read my response to your previous post, this will allow us to determine if the...
Forum: Amplified Tube Subwoofers 09-25-2017, 08:54 AM
Replies: 9
Views: 199
Posted By heavyduty
Re: Bazooka BTA10100 not working correctly please help!

Grab your DMM, and measure the voltage of the output leads. If the amplifier is working, you will see voltage at the terminals. If there is no voltage, the amplifier is not working.
Forum: Amplified Tube Subwoofers 09-23-2017, 08:25 PM
Replies: 9
Views: 199
Posted By heavyduty
Re: Bazooka BTA10100 not working correctly please help!

Just curious as to why you did not tap into the factory harness after the amp? I would remove the back plate or the driver and check to make sure that one of the speaker connections has not come...
Forum: Amplified Tube Subwoofers 09-23-2017, 07:34 PM
Replies: 9
Views: 199
Posted By heavyduty
Re: Bazooka BTA10100 not working correctly please help!

The end plates for the BTA10100 and the BTA10250 are different. As for the problem you are experiencing, do you have any output from the rest of the factory stereo?

What happens if you unplug the...
Forum: Marine Audio 09-12-2017, 07:58 AM
Replies: 5
Views: 291
Posted By heavyduty
Re: Marine Tubbies Muffled 8"

It could have been a clipping issue of the amplifier, DC voltage will kill a voice coil. Or, the voice coil lost alignment. It happens. Give Customer Service a call and ask about a replacement. ...
Forum: Marine Audio 09-11-2017, 10:12 AM
Replies: 5
Views: 291
Posted By heavyduty
Re: Marine Tubbies Muffled 8"

Yes, if the voice coil is bad, or is out of alignment, any movement of the cone, powered or passively, will result in noise. As for the front 6.5", does this speaker make noise at all volumes?
Forum: Marine Audio 09-09-2017, 12:45 PM
Replies: 5
Views: 291
Posted By heavyduty
Re: Marine Tubbies Muffled 8"

Sounds like a voice coil has gone bad. Call 1-800-THE-TUBE, on Monday to discuss the appropriate remedies. Just keep in mind, Irma may have other plans, so if you do not get an answer, don't forget...
Forum: Amplified Tube Subwoofers 09-08-2017, 10:21 AM
Replies: 1
Views: 134
Posted By heavyduty
Re: RCA Inputs

Yes, you do need both of the RCA jacks. Trace the patch cord back to the source, to make certain you do not have one unplugged. Also, have you tried switching out patch cords?
Forum: General Chat 08-23-2017, 11:50 AM
Replies: 5
Views: 437
Posted By heavyduty
Re: Old school VS new amplified

If you have the room, I say purchase the salve unit. It will be an upgrade from you existing pair of 8" Tubes. Another great bonus with the 250D, it will perform flawlessly at 2 ohm's mono.
Forum: General Chat 08-22-2017, 10:22 AM
Replies: 5
Views: 437
Posted By heavyduty
Re: Old school VS new amplified

Yes, use your existing RCA's, constant +12v, remote turn-on and ground connections, and connect to the BTA10250D. Don't forget to purchase your BT1014, and get ready to drop some wicked low's.
Forum: General Chat 08-21-2017, 01:19 PM
Replies: 5
Views: 437
Posted By heavyduty
Re: Old school VS new amplified

If you have the room, go with the 10" BTA10250D. There is no replacement for displacement.
Forum: Hook me up! 08-21-2017, 01:18 PM
Replies: 1
Views: 335
Posted By heavyduty
Re: Powered Bazooka Tube (NOS8)

Yes, your son has purchased a passive NOS8. The red and blue wires are the speaker wires, and these colors are used to keep with the NOS scheme. You can use the red for the positive terminal...
Forum: Amplified Tube Subwoofers 08-02-2017, 12:41 PM
Replies: 21
Views: 971
Posted By heavyduty
Re: BTA10200 - did i break it?

The back plates should bolt right into place. Give Cathy a call, (1-800-THE-TUBE), and explain the situation, that the A200 amp is dead and you would like to upgrade, there may be a trade-in credit....
Forum: Amplified Tube Subwoofers 08-02-2017, 10:46 AM
Replies: 21
Views: 971
Posted By heavyduty
Re: BTA10200 - did i break it?

You have absolutely exhausted every possibility. Yes, you can remove the amplifier from the Tube and take a look at the board, as well as the components. It could be a minor component that needs to...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 01:48 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Template-Modifications by TMS
bazooka.com
SAS, BAZOOKA, BASS TUBES, and LISTEN TO YOUR EARS are registered trademarks of Southern Audio Services, Inc.